Home  |  My Account  |  Help
Source Code: WZDARUNK | September 4, 2010
SHOPPING CART
ITEMS: 0 TOTAL: $0.00
VIEW CART / CHECK OUT
| | | | |


Summer 2010 Pool Supplies Winterizing Kits Above ground Winter Covers In Ground Winter Covers Safety Covers Pool Closing Accessories

Spa2Go Four Person Portable Spa


Enjoy a whirlpool spa wherever you like without complicated or installation, thanks to this portable unit that inflates in minutes and has all the heated jet action of permanently installed models.
  • Installation Instructions


  • Specifications and Dimensions


  • Watch The Spa2Go Video


  • Warranty:
  • FINALLY, THE WORLD'S MOST AFFORDABLE AND TRULY PORTABLE SPA!

    • Enjoy a relaxing whirlpool spa wherever you like without complicated or costly installation, thanks to this portable unit that inflates in minutes yet has all the vigorous heated jet action of permanently installed models.

    • With enough space for four adults, the spa has ample room to relax and enjoy a full 250 gallons of heated turbojet water that rejuvenates and soothes tight, tired muscles.

    • Enjoy your Spa2Go in just minutes! Inflate, plug into a standard 110v outlet and fill from a garden hose. The accompanying motor inflates the spa in ten minutes, and the pump system includes a filter unit to make sure the water remains fresh.

    • Adjust the water temperature to your preferred heat level at the touch of a button thanks to the spas digital thermostatic control panel.

    • Spa2Go includes a built-in seat, cushioned side panels for reclining comfort and a locking cover.

    • The durable K80 vinyl construction is the same resilient material found in white water rafts to deflect pulling, tearing, and punctures.
    Allow 7-10 days for shipping of this item.

    Qty. Item No. Item Name ONLY! 
    4 Month
    Payment Plan
     
    Q2055  
    Hot  Easy Pay  
    Spa2Go   $649.99   $162.50  


    Technical Specifications:

  • Outside diameter 74" (with power pak 98")
  • Inner Diameter 58"
  • Height 28"
  • 250 gallon capacity
  • 1.3 HP Turbo Wave Massage System
  • 127 Micro-Air Jets
  • 15 sq ft Filtration system
  • Thermostatically Controller 1kw Heater
  • 10’ power cord
  • Weights 2245 lbs when full
  • Massaging Turbo Blower: 1 HP
  • Pump: Fractional HP Circulation Pump
  • Heater: Stainless steel , 1000W


  • Back To The Top

    Troubleshooting:

    Air Pump Blower:

    Turbo wave pump will not turn on:
    - Make sure the power pack is plugged into the electrical outlet, and that there is power to the outlet. Plug another electrical item into the outlet such as a hair dryer or lamp. If you do not have power, check the breakers at the main electrical panel.
    - Test the GFCI per the instructions in the Maintenance section of this manual. If the GFCI is faulty do not use the spa. Immediately call your dealer or the factory for instructions. DO NOT BYPASS THE GFCI! DO NOT USE THE SPA!

    Turbo wave pump will not turn off:
    - Call the factory for instructions.

    Turbo wave pump blower trips the GFCI when you turn it on:
    - Take the air loop off the top of the power pack. Look down inside the left fitting and see if water has collected inside the power pack.
    - If water has collected inside the power pack, disconnect the large fitting connecting the power pack to the spa. Ensure the check valve in the fi tting is in place and working properly.

    Spa2Go

    No Heat:
    - Dirty filter: Clean the filter per the instructions provided in the Maintenance section of this manual. If the filter is more than two months old, replace it. After cleaning or replacing the filter, cover the spa, turn the temperature set point all the way up, and leave the spa for 24 hours. If the spa still will not heat, contact the manufacturer for instructions.
    - No circulation, water pump air bound: Unplug the power pack from the electrical outlet. Bleed air from the filter tank by turning the bleed fitting on the top of the filter tank counter-clockwise. After one minute, or when water drips from the fitting, close the bleed fitting and plug in. If the water pump still does not pump water, contact the manufacturer for instructions. If the water pump becomes air bound again, check the o-ring on the top of the filter tank. Refer to the filter changing instructions in the Maintenance section of the manual. Replace the o-ring if necessary.
    - Bad power pack: Ensure power is available to the spa. Check the circuit breaker at the main electrical panel. Connect another electrical appliance to the plug used for the spa. If power is available to the spa, test the GFCI using the instructions supplied in the Maintenance section. If the GFCI is working properly and the power pack does not function, then the power pack is bad. If the GFCI is not working properly, do not use the spa. Immediately contact the manufacturer for instructions.
    - In some situations, the numerical temperature display may read ‘OH’ (overheat) and the spa will not heat until reset. To fi x this problem, please use the following procedure:
    1.If the spa water is still warm (over 104°F / 40°C), unplug the power pack and let the water cool to below 104°F / 40°C. (Use a thermometer to verify the temperature.)
    2. Plug the power pack back in and press the small reset button directly below the temperature display. This will clear the ‘OH’ message and the spa will resume normal operations.

    Leaking Problems:
    - The two small connections between the power pack and the spa are leaking: Ensure the garden hose style washer inside each of these fi ttings is still in place and undamaged. If the washers are in place and the connection is still leaking, there may be a small piece of plastic behind the hose washer. Remove the small piece of plastic with a utility knife or needle-nose pliers.
    - Blower connection is leaking: If the large connection between the spa and the power pack is leaking, ensure the o-ring inside the fi tting is in place and undamaged.
    - Plumbing or pressure switch is leaking: Look under the power pack. If water is coming from underneath the power pack, then the plumbing or pressure switch inside the power pack is leaking. Contact the factory for instructions.


    Back To The Top




    Related Items
      Click to enlarge image


       « Previous  Product 12 out of 13 in Portable Spas & Hot Tubs  Next »   


    Shop the Best Brands in the Pool Business! Visit Our Superstore Pages Below.

      SIGN UP FOR WEEKLY EMAIL PROMOTIONS  

    Customer Service
    · Measuring Forms
    · Water Testing
    · FAQs
    · Contact Us

    Shopping
    · My Account
    · Shipping & Returns
    · Order Tracking

    Company
    · About Us
    · Employment
    · Privacy & Security
     Catalog
    · Request a Catalog
    · Place a Quick Order

    HACKER SAFE certified sites prevent over 99% of hacker crime.
    In The Swim- America's #1 Direct Source For Pool Supplies

    In The Swim®
    320 Industrial Drive
    West Chicago, IL 60185
    1-800-288-7946